Isys Iterra Mi875 Manuel d'utilisateur

iTerr

December 2011: Revision 001 10 iTerra Mi875 Top View Printhead Latch Input Ink Tubes Output Ink Tubes Clamshell latches

December 2011: Revision 001 11 Turn Around Latches Turn Around Latch Releases

December 2011: Revision 001 12 iTerra Mi875 Peripherals Input Media Basket Output Media Basket

December 2011: Revision 001 13 6. iTerra Mi875 Rear View Power connector USB connection Ethernet Connection Serial connection

December 2011: Revision 001 14 7. iTerra Mi875 Side View

December 2011: Revision 001 15 8. iTerra Mi875 Consumables The iTerra Mi875 comes with a printhead and a set of 5 cartridges – 1 Cyan, 1 Mag

December 2011: Revision 001 16 9. Unpacking the Printer Open the printer box. With two people, remove the printer and place on an even surf

December 2011: Revision 001 17 STEP 5 STEP 6 Power up the printer. Open the printer to expose the engine. From the menu, select: 1

December 2011: Revision 001 18 STEP 7 STEP 8 Orient the printhead so the flex is towards the connectors. Angle the printhead back towards

December 2011: Revision 001 19 10. Loading Media Paper Path Printhead Service Station Turn-around Ink Cartridges Take up rollers Cu

December 2011: Revision 001 2 1. Table of Contents 1. Table of Contents ...

December 2011: Revision 001 20 STEP 1 STEP 2 Open the box of media. Place the media in the input basket with the tickmark showing. IMPO

December 2011: Revision 001 21 11. User Interface Panel Main Menu  Online – toggles between Online and Offline  Shutdown – performs a cl

December 2011: Revision 001 22 Interface Menu Page 1 The user interface options on Page 1 are:  Plot Control o allows the user to increase

December 2011: Revision 001 23 Printhead Maintenance The options from this screen are:  a user initiated clean of the printhead, either l

December 2011: Revision 001 24 Adjustments The adjustments allow modifications to the time the rollers feed in paper or retract paper. The

December 2011: Revision 001 25 Page 3 Page 3 gives access to the Control Panel menu settings, and setting and configuring the network. Co

December 2011: Revision 001 26 Network Settings Network Settings allow the user to set the values for an IP address, the Subnet Mask and the

December 2011: Revision 001 27 Printer Maintenance Menu Cleaning the Printheads 1. Turn the printer Offline 2. Select Menu 3. Select Main

December 2011: Revision 001 28 Printer Adjustments and Information Adjustments 1. Turn the printer Offline 2. Select Menu 3. Select until

December 2011: Revision 001 29 8. Press the up or down arrow to change the LCD contrast setting 9. Press Save 10. Down arrow to Exit to Off

December 2011: Revision 001 3 Getting Ready to Move the Printer...

December 2011: Revision 001 30 8. When the arrow is flashing, use the up and down arrows to adjust the value 9. When you have set the desire

December 2011: Revision 001 31 12. Common Display Panel Procedures It is important to follow these procedures when performing routine tasks

December 2011: Revision 001 32 13. Toolbox The Toolbox is an alternate option for viewing printer status and configuring various parameters i

December 2011: Revision 001 33 Main Screen Menu The Toolbox main menu. From here, you can monitor the status of the printer and navigate to v

December 2011: Revision 001 34 Diagnostics The diagnostic page display information about the print engine unit. Diagnostic prints can be ge

December 2011: Revision 001 35 Network Configuration The network values can be set in this page. NOTE: Do NOT change the printer name. It i

December 2011: Revision 001 36 14. Replacing Consumables Replacing Ink Cartridges STEP 1 STEP 2 Open the front cover. Open the latch

December 2011: Revision 001 37 Replacing the Printhead STEP 1 STEP 2 Deprime the printhead:  Follow the procedure outlined in Getting

December 2011: Revision 001 38 STEP 7 STEP 8 Gently place the printhead in the printer, then push forward until the printhead is in pla

December 2011: Revision 001 39 Out of Paper If a print job runs out of paper part way through, perform the following: 1. From the main menu

December 2011: Revision 001 4 2. Limitation of Liability The Imaging Systems Group’s total liability to the purchaser, or to any third party

December 2011: Revision 001 40 15. Trouble Shooting Clearing Paper Jams NOTE: When removing jammed paper, do NOT attempt to pull paper thro

December 2011: Revision 001 41 STEP 5 Reload the paper into the input slot. Make sure a page without a tick mark is the first page. Turn t

December 2011: Revision 001 42 Blank Pages If your printer is putting out blank pages only, check the following:  open the lid of the printe

December 2011: Revision 001 43 16. iTerra Mi875 Specifications Printer Specifications PRINT TECHNOLOGY Color InkJet PLOTTER CARRIAGE WIDTH 8

December 2011: Revision 001 5 3. iTerra Mi875 Warranty The Imaging Systems Group Inc. (iSys) warrants the iTerra Mi875 (Product) to be free

December 2011: Revision 001 6 4. Safety Information 120 Volt Models Your iSys product has been carefully designed to give you years of saf

December 2011: Revision 001 7

December 2011: Revision 001 8

December 2011: Revision 001 9 5. iTerra Mi875 Front View Letter Part A Display Panel B Paper Output Slot C Holding Screws for Paper